4db原则（法则）-英文原文 -福禄克DSX2-8000/DTX-1800-深圳连讯

400-996-0787

首页 新闻中心 技术文章

返回

新闻中心

联系我们

全国统一服务热线：

134 1039 1245
400-996-0787
0755-8399 9818
联系邮箱：

sales@faxytech.com
联系地址：

深圳市福田区华强北路华联发大厦602室

4db原则（法则）-英文原文 -福禄克DSX2-8000/DTX-1800

A YouTube video explaining how this this works is also?available from here.

This is applicable to the following cabling standards only:

ISO/IEC 11801

EN 50173

Aus/NZ

JIS

When?the Insertion Loss is less than 4.0 dB at the frequency point where the measurement is made, then the measurement is ignored and not uated against the selected Test Limit/Cabling Standard in the DTX CableAnalyzer. This is often referred to as the 4 dB rule. It is not applied in the North American TIA Cabling Standards. Only certain test parameters and configurations will have the 4 dB rule. The tables below indicate which link? definitions and test parameters have the 4 dB rule applied to them. As an aid, the other rules are also listed.

On a?short link, the Insertion Loss may never reach 4.0 dB. If that were to happen, then the entire measurement would be?ignored, or as the cabling standards phrase it; “recorded for information only”. If this were to happen with your DTX CableAnalyzer, you would see an “i” appear next to the summary result for that test parameter. In LinkWare software, the result would be recorded with “N/A’. An example is shown below:

Concern is normally caused when the result has a negative margin. In this example we see the NEXT margin was -9.7 dB. A?negative margin is normally associated with a FAIL, but because the entire link never exceeded 4.0 dB Insertion Loss, it’s not a FAIL. Further?confusion lies in that the North American ANSI/TIA/-568-C.0 cabling standard does not have this 4 dB rule. If you were to test the same link above?with the same DTX CableAnalyzer, but using the North American Standard TIA Cat 5e Perm. Link, your result would be a FAIL.

Please make sure you?have agreed in a Test Limit, in writing, before the project starts.

Let’s review in detail how this works by looking at another example test result on the DTX CableAnalyzer.

An ISO11801 PL Max Class D AUTOTEST was run on a short 6.0 m installed link, giving the following result:

Looks normal. Let’s take a look at the NEXT result in a little more detail:

You will observe that?the limit line has two colors, black and red. The cabling standards do not require the cable tester manufacturer to display where the 4 dB rule is implemented to the user, only that it is implemented. However, the DTX CableAnalyzer will indicate where the 4 dB rule has been implemented by changing the color of the limit line. If the?limit line is black,?the Insertion Loss was less than 4.0 dB. If?the limit line is red,?the Insertion Loss was 4.0 dB or greater. So for this Pair 1,2-4,5 the NEXT is not uated below 84.8 MHz. Let’s take a quick look at the Insertion Loss for Pair 4,5:

As you can see, the Insertion Loss reached 4.0 dB at 84.8 MHz, as previously indicated in the NEXT Pair 1,2-4,5 graph above. NEXT contains two pairs. So which Insertion Loss pair do we use to implement the 4 dB rule? The disturbed pair is used for uation purposes. So if the worst case NEXT Pair was 1,2-7,8 then the?DTX CableAnalyzer would use the Insertion Loss values from Pair 7,8 to determine where the 4 dB rule is implemented.

As previously mentioned, if the link is particularly short, then the Insertion Loss may never reach 4.0 dB and the entire NEXT result is “ignored”. Let’s take a closer look at the first example where the test result was:

Looking at the worst case NEXT result, we see the entire limit line is black, suggesting that the Insertion Loss for Pair 4,5 never reached 4.0 dB:

Looking at the Insertion Loss for Pair 4,5:

We see that the Insertion did indeed never reach 4.0 dB, so the entire measurement is not uated against the limit line (ignored) and recorded as “i” Information Only. If this result was downloaded to LinkWare Software, the report would show N/A against this measurement:

No further action is required by the installer. This is a valid standards compliant result.

目录

首页

销售品牌+

Fluke/福禄克工业仪器+

红外热像仪+

测温仪+

数字万用表+

数字钳形表+

绝缘电阻测试仪+

接地电阻测试仪+

示波器+

蓄电池电阻分析仪+

电能质量分析仪+

安规测试仪+

过程校准器+

回路校验仪+

压力校验仪+

温度校验仪+

测距仪+

粒子计数器+

多功能环境测试仪+

照度计+

空气质量检测仪+

风速仪+

安装测试仪+

激光对中仪+

测振仪+

数据采集器+

医疗测试+

配件/工具+

NetAlly（原NetScout）+

有线网络测试仪+

无线网络测试仪+

有线+无线网络测试仪+

Fluke Networks/福禄克网络仪器+

网线测试仪+

网络测试仪+

光纤测试仪+

配件/工具+

FLIR/菲力尔+

红外热像仪+

Raytek/雷泰仪器+

红外测温仪+

在线式红外测温仪+

KEYSIGHT/是德（原Agilent/安捷伦）+

数字万用表+

电源+

示波器+

VIAVI（原JDSU）+

光时域反射仪（OTDR）+

光功率计+

光源+

EXFO（加拿大EXFO）+

光时域反射仪（OTDR）+

光功率计+

光源+

Tektronix/泰克+

数字万用表+

示波器+

数据采集器+

信号发生器+

图形源表SMU仪器+

配件+

Megger/梅凯（梅格）+

绝缘电阻测试仪+

继电保护测试仪+

低电阻测试仪+

接触电阻测试仪+

接地电阻测试仪+

FOTRIC/飞础科+

红外热像仪+

配件+

KYORITSU/共立（克列茨）+

绝缘电阻测试仪+

SUMITOMO/住友+

光纤熔接机+

Fujikura/藤仓+

光纤熔接机+

YOKOGAWA/横河+

光时域反射仪（OTDR）+